Configuring DD-WRT on the Linksys WRT1900ACS for Multiple WiFi SSID and VPN Setup

Configuring the Linksys WRT1900ACS From Scratch

New DD-WRT firmware for the WRT1900AC
Aug 11, Messages: The dd-wrt forum where this is discussed is: If you'd like to post a question, simply register and have at it! However, I own a HDHomerun connect, connected to my router via the lan port and I have been unable to get it to work. Since i wasn't able to go back to stock, I went all the way back to a dd-wrt Beta version Kong from January and that resolved my issue. There hasn't been a stock firmware update since June and that includes the V2.

Advanced Home Networking In 2017

Linksys WRT1900ac/1200ac - revert to stock from DDWRT

Thanks a lot for the guide. I just installed dd-wrt on my ac linksys router. Hi, I used similar instructions on my linksys wrtacs running dd-wrt. It has preformed well, I have experienced quite a loss in download speeds but have maintained consistent upload speeds. However, I own a HDHomerun connect, connected to my router via the lan port and I have been unable to get it to work.

Would you have any idea what settings may be preventing this device to work? I plan on contacting SiliconDust support but was reading this article and thought you may have more insight being familiar with dd-wrt. Thank you in advance. Are you using OpenVPN? Thanks a lot man.

This was exactly what i needed. Hi Ray, great guide! Thank you very much for this tutorial. I am looking for this answer too, for the wrtacs v2, it is possible to create vlans with the Ethernet ports? As some with ssids? It has been a while. Here is the firmware for version 2 of this router. Thanks for such great tutorial. I was able to setup the VPN and auth1.

However all the VPN traffics got timeout. I flashed my wrtacs and everything went well. The only problem I am having is that my 5ghz wifi is passwordless, despite setting a password over and over again.

Some advice would be appreciated. Just a few questions… 1 what happens if the VPN connection drops? Did you implemented some kind of internet kill switch?

Hi Ray… thanks for the tutorial. Easy to follow and very detailed. I do have an issue… I follow the instructions and perform a firmware upgrade through the linksys setup page. It goes well, loads the file and reboots. But when I go back to load the configuration page again it goes back to the linksys setup page. I have reset the router to factory multiple times prior to attempting to load the firmware.

Everything point to it loading fine, but when I try to log back on, same old linksys menu. Thanks for your help. Your email address will not be published. While you're at it, please check out SmallNetBuilder for product reviews and our famous Router Charts , Ranker and plenty more! Discussion in ' General Wireless Discussion ' started by sfx , Aug 20, Log in or Sign up.

This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Dismiss Notice Welcome To SNBForums SNBForums is a community for anyone who wants to learn about or discuss the latest in wireless routers, network storage and the ins and outs of building and maintaining a small network.

Aug 11, Messages: Kong has created a firmware that will allow folks to revert back to Linksys factory firmware if one has accidentally flashed both banks with 3rd party FW RogerSC , Oct 30, Just click on this link before you buy something from Amazon and we'll get a small commission on anything you buy.

Aug 1, Messages: I'm hoping for Tomato for this router at some point. There hasn't been a stock firmware update since June and that includes the V2. Apr 14, Messages: RMerlin , Nov 3, I know but one can wish. Might as well just do everything from the CLI. So Roger, do you know if there's any difference between what Kong is doing and what Brainslayer is doing? The latest discussions in that thread are about BS version.

Aug 11, Messages: The Network Map is still horribly buggy and it causes issues. I'm also having issues with my AirPrint printers that seem to be only solvable by a reboot.


Jan 07,  · kong says that the reason why dd-wrt does not support marvell based routers is because there is a small number? i was friggin hyped for the wrtac, but now i feel disappointment with doubt. Is everything okay? DD-WRT Preview for Linksys® WRTAC/WRTAC January 15, Following Linksys’ CES announcement made on Jan 05th in Las Vegas accompanied by a first preview version for the Linksys WRTAC now also versions for the WRTAC, WRTAC v2 & WRTACS are available via DD-WRT’s router database. The WRTAC is a dual band router. The two bands correspond to two physical interfaces in the Wireless/Basic Settings webpage. ath0 is .