How to use a router as a repeater

Question Info

How to Extend Wi-Fi Network Using an Old Router as a Repeater
There's bound to be a room in your house where Wi-Fi coverage is patchy. Take a smartphone, tablet or laptop, and check to see the signal strength when close to each of the routers. Resetting the router and starting from scratch is the best practice to follow. Remember this address as you might need it to access this router later. When a computer is to be located more than feet from the nearest Ethernet access point, a device known as a repeater will need to be used to maintain a signal that is strong enough to enable network communications.

Related Articles

How to Use a Router as a Repeater

This setting should be on the same page as the IP address, but each router is a little different. When the router is operating normally, this server assigns an IP address to every device that is connected to it.

Because this router will be used as a repeater only, the IP addresses will now be handled by the main router on the network. Turn off the DNS server, if it is activated.

This function will be taken over by the main router, or by the ISP that provides the Internet connection to your location. Disable any firewall that is built into the router. Usually, this can be done in the "Security" section, and it may require you to alter several settings, depending on the make and model of the router. Remove any entries that are located in the "Port Forwarding" section. On some routers, this may be referred to as "Applications and Gaming," and it allows certain programs to have less-restricted access to the Internet.

Set the operating mode switch to "Gateway" or "Switch" if such a setting is available. In addition, if the router is a wireless router and has the appropriate settings, disable the wireless access or set it to function as an access point only. The best way to do this is to turn off your main router for a few minutes while you set up this slave router.

If you only have one PC you will have to disconnect it from your working network temporarily. Once attached, go through Step 1 again with this router until you get to the stage where you have accessed the configuration page.

Here, we're using a D-Link router. Ignore any setup wizards, and go to the Wi-Fi settings page. Enable wireless, change the wireless network name to be the same as the primary router and choose a channel well away from channel 6, which is what the primary router is using.

Match the security type exactly and type in the same password you use for Wi-Fi on your primary router.

Finally you need to make the slave router work alongside the primary router by giving it a fixed IP address which the primary router will recognise and work with. Head to the LAN setup page or simialr and give the router an IP address in the same range as the IP addresses given out by my main router, but outside of the range that is automatically assigned by DHCP.

Dynamic Host Communications Protocol is the process by which a device issues IP addresses to equipment on the network. You need to stop the slave router giving out IP addresses to devices, leaving that task in the hands of the primary router. Disable DHCP by un-ticking it on the relevant configuration page. To assign a fixed IP address, let's assume the main router has an address of Give the slave router an IP address of Remember this address as you might need it to access this router later.

Remember, too, that once you've change the router's IP address you will have to wait for it to reboot, and then access it by typing the new IP address into your browser's address bar. Now we are ready to connect it all together. The ideal way to connect two routers together is with a long network cable. However, this is usually impractical so the best alternative is to use cheap powerline networking adapters.

These work by using the mains power cables in your walls and floors to act as network cables as well as passing electricity through them. Just like most broadband connections, the wire for the router was pulled inside from the corner of the flat. Everything was fine unless we were using the internet connection in the kitchen or the balcony.

I was able to extend the range of my Wi-Fi by turning an old router into a repeater and I documented all the steps involved in it. So if you need a helping hand in setting up your home wireless connection, read on. The very first thing you need to do is find out the details of the Wi-Fi connection you are currently connected to. Make a note of these settings on a notepad before proceeding to the next step.

After you have all the necessary details from the primary router, plug in your old adapter and reset it to factory settings.

Most of the time there is a dedicated reset key or you might have to press and hold the WPS button for a few seconds.

Video of the Day

Click the Setup tab up top, then the Basic Setup sub-tab if not selected by default. Scroll down to the Network Setup section. Change your local IP address to something other than the local IP address of your primary router. 5. Configure your second router. Connect this second router now, with a network cable, to a PC which is not on your network. The best way to do this is to turn off your main router for a few minutes while you set up this slave router. If you only have one PC you will have to disconnect it from your working network temporarily. Aug 22,  · On this AP is a mode called "AP Mode" off the Setup tab. From there it is pretty easy to setup. Just select the button that reads "Wireless Repeater". Enter the MAC address to your primary router and there you go. Setup security you you want it and you have effectively expanded you wireless network range for the wireless devices .