How to use a router as a repeater

Step 1: Getting the Wi-Fi Details from the Main Router

How to Extend Wi-Fi Network Using an Old Router as a Repeater
The very first thing you need to do is find out the details of the Wi-Fi connection you are currently connected to. It may ask for a user name and password. After the router boots back up, the changes should allow it to act more or less as a simple repeater. Connect your computer to the router using a standard Ethernet cable. There's bound to be a room in your house where Wi-Fi coverage is patchy.

Related Articles

How to Use a Router as a Repeater

Usually, this can be done in the "Security" section, and it may require you to alter several settings, depending on the make and model of the router. Remove any entries that are located in the "Port Forwarding" section. On some routers, this may be referred to as "Applications and Gaming," and it allows certain programs to have less-restricted access to the Internet.

Set the operating mode switch to "Gateway" or "Switch" if such a setting is available. In addition, if the router is a wireless router and has the appropriate settings, disable the wireless access or set it to function as an access point only. Save the settings as necessary on each page, and reboot the router. After the router boots back up, the changes should allow it to act more or less as a simple repeater.

Now, you simply move the router to its new location in the middle of the long cable run, connect all the cords and power it up.

How to Use a Router as a Repeater. Share Share on Facebook. You can use a router as a repeater to boost signal strength. Everything was fine unless we were using the internet connection in the kitchen or the balcony. I was able to extend the range of my Wi-Fi by turning an old router into a repeater and I documented all the steps involved in it.

So if you need a helping hand in setting up your home wireless connection, read on. The very first thing you need to do is find out the details of the Wi-Fi connection you are currently connected to. Make a note of these settings on a notepad before proceeding to the next step. After you have all the necessary details from the primary router, plug in your old adapter and reset it to factory settings. Most of the time there is a dedicated reset key or you might have to press and hold the WPS button for a few seconds.

Resetting the router and starting from scratch is the best practice to follow. Connect this second router now, with a network cable, to a PC which is not on your network. The best way to do this is to turn off your main router for a few minutes while you set up this slave router. If you only have one PC you will have to disconnect it from your working network temporarily. Once attached, go through Step 1 again with this router until you get to the stage where you have accessed the configuration page.

Here, we're using a D-Link router. Ignore any setup wizards, and go to the Wi-Fi settings page. Enable wireless, change the wireless network name to be the same as the primary router and choose a channel well away from channel 6, which is what the primary router is using. Match the security type exactly and type in the same password you use for Wi-Fi on your primary router. Finally you need to make the slave router work alongside the primary router by giving it a fixed IP address which the primary router will recognise and work with.

Head to the LAN setup page or simialr and give the router an IP address in the same range as the IP addresses given out by my main router, but outside of the range that is automatically assigned by DHCP.

Dynamic Host Communications Protocol is the process by which a device issues IP addresses to equipment on the network. You need to stop the slave router giving out IP addresses to devices, leaving that task in the hands of the primary router. Disable DHCP by un-ticking it on the relevant configuration page. To assign a fixed IP address, let's assume the main router has an address of Give the slave router an IP address of Remember this address as you might need it to access this router later.

Remember, too, that once you've change the router's IP address you will have to wait for it to reboot, and then access it by typing the new IP address into your browser's address bar. Now we are ready to connect it all together. The ideal way to connect two routers together is with a long network cable. However, this is usually impractical so the best alternative is to use cheap powerline networking adapters.

Video of the Day

Unplug your computer's Ethernet cable, turn on a wireless device, and see if you can find your new repeater bridge. Connect to it, use the same password you'd use for the main router, and you should have success. If not, run through the . How to use a router as a repeater If you have a large house or simply a Wi-Fi blackspot, you can use a second router to cure the problem. Here's our helpful guide on how to set up a spare wireless router to act as a repeater. solved Can LAN ports of Tenda n router be used while router is configured as wireless repeater. Using two router/ a router and a repeater as "Wireless .